Save Hundreds on Your Rentals

Fill out our form - takes 30 seconds - Enjoy Competing Quotes

Construction Equipment Rental in Austin, Arkansas

Our vast network of vendors in Austin Arkansas offers a huge, ready to rent inventory of heavy construction equipment.

Do you have any immediate requirements? Call our toll free number today!

You can also get in touch by filling up the contact form on the right (will take less than a minute).

Several contractors in the region have begun approaching us for flexible construction equipment rental services in Austin. We have the best suppliers onboard who have a reputation of providing top notch construction tools and heavy machinery; rent agreements are highly flexible and prices affordable. Needless to mention, you need not worry about the pick-and-drop services too.

As you move forward on the growth path, you need a healthy cash flow, strong credit lines and flexibility in deploying the right equipment at the right time for a construction job at hand. We can assist you with the latter very well.

Equipment Rental Austin, Construction equipment rental Austin, Construction rental Austin, Heavy Equipment Rental Austin.

New Holland Skid Steer Loader L218

L218_main
THE SUPER BOOM® ADVANTAGEN
New Holland's patented Super Boom® vertical lift geometry provides maximum reach at the top of the lift curve, making it perfect for loading materials over the side of trucks and placing load in the center of the vehicle.

Engine
Manufacturer/model ISM / N844LT
Bore/stroke, in (mm) 3.31 x 3.94 (84 x 100)
Displacement, in3 (L) 135 (2.2)
Fuel injection HPCR Direct
Air intake Turbocharged Aftercooled with external EGR
Horsepower per SAE J1349 Gross hp (kW) 60 (45) @ 2800 rpm
Horsepower per SAE J1349 Net hp (kW) 57 (42) @ 2800 rpm
Peak torque, lb-ft (Nm) 135 (183) @ 1800 rpm
Power Train
Travel speed, low range, mph (km/h) 7.4 (11.9)
Travel speed, high range (optional),mph (km/h) 10.8 (17.4)
Dimensions
HEIGHT TO
Bucket hinge pin, in (mm) 120 (3048)
Top of ROPS, in (mm) 77.7 (1974)
Bottom of level bucket, fully raised,in (mm) 113.3 (2877)
Overall length without attachment with coupler, in (mm) 105.7 (2697)
Dump angle, degrees 52°
Dump reach (max height), in (mm) 30.8 (783)
Rollback, bucket on ground, degrees 35°
Rollback, bucket at full height, degrees 88°
Wheelbase, in (mm) 44.4 (1128)
Ground clearance (bottom of belly pan),in (mm) 7 (178)
Angle of departure, degrees 23°
Clearance circle without bucket, in(mm) 50.7 (1289)
Clearance circle rear, in (mm) 62.9 (1599)
Rear axle to bumper, in (mm) 36.4 (924)
Overall width, in (mm) 66.1 (1678)
Hydraulic System
Pump flow, Standard Flow, gpm (Lpm) 20.6 (78)
Relief pressure, psi (bar) 3046 (210)
Optional high flow, gpm (Lpm) 30.7 (116.2)
Performance Specs
Rated operating load, 50% tip, lbs (kg) 1800 (818)
Tipping load, lbs (kg) 3600 (1633)
Breakout force, lift cylinder, lbs (kN) 2620 (11.7)
Breakout force, bucket cylinder, lbs (kN) 5550 (24.7)
Operating weight, lbs (kg) 5930 (2690)

Komatsu Dozers D61EX-23

D61EX-23 Crawler Dozer

Hydrostatic drive gives the Komatsu Dozers D61EX-23 operator incredible control with tremendous pushing power. The super slant nose design gives the operator the balance he needs for high precision grading. Komatsu's Tier 4 interim solution lets the operator work during regeneration. To make the operator more comfortable and productive, a new air suspension heavy duty heated seat is standard.

Engine
Model Komatsu SAA6D107E-2*
Type 4-cycle, water-cooled, direct injection
Aspiration Komatsu variable geometry Turbocharged, air-to-air aftercooled
Number of cylinders 6
Bore x stroke 4.21" x 4.88" 107 mm x 124 mm
Piston displacement 408 in³ 6.69 ltr
Governor All-speed and mid-range, electronic
Horsepower
SAE J1995 - Gross 170 HP 127 kW
(ISO 14396 169 HP 126 kW
ISO 9249 / SAE J1349 - Net 168 HP 125 kW
Rated rpm 2200 rpm
Fan drive type Hydraulic
Lubrication system:
Method Gear pump, force lubricationn
Filter Full-flow
Hydrostatic transmission
Dual-path, hydrostatic transmission provides infinite speed changes up to 9.0 km/h 5.6 mph. The variable capacity travel motors allow the operator to select the optimum speed to match specific jobs. Travel control lock lever and neutral switch.
Travel speed (quick shift mode)* Forward Reverse
1st 0-3.4 km/h 0-2.1 mph 0-4.1 km/h 0-2.5 mph
2nd 0-5.6 km/h 0-3.5 mph 0-6.5 km/h 0-4.0 mph
3rd 0-9.0 km/h 0-5.6 mph 0-9.0 km/h 0-5.6 mph
Travel speed (variable mode) 0-9.0 km/h 0-5.6 mph 0-9.0 km/h 0-5.6 mph
*Quick shift speeds are adjustable in the monitor.
FINAL DRIVE
In-shoe mounted axial piston type travel motors with integrated two-stage planetary gear reduction. Compact in-shoe mount reduces risk of damaged by debris. Bolt-on sprocket teeth for easy displacement.
STEERING SYSTEM
Palm Command Control System (PCCS) joystick control for all directional movements. Pushing the joystick forward results in forward machine travel, while pulling it rearward reverses the machine. Simply tilt the joystick to the left or right to make a turn. Tilting the joystick fully to the left or right activates counter-rotation.
HYDROSTATIC TRANSMISSION (HST) provides smooth powerful turns. Fully electronic control enables smooth control that can be adjusted in the monitor. The PCCS utilizes shift buttons to increase and decrease speed.
Minimum turning radius (as measured by track marks on the ground at pivot turn.) 83"
Undercarriage
Suspension Oscillating-type with equalizer bar and pivot shafts
Track roller frame Monocoque, large section, durable construction
Rollers and idlers Lubricated track rollers
Lubricated tracks Parallel Link Undercarriage System (PLUS) with lubricated rotating bushings for extended system wear life and lower maintenance costs. Track tension is easily adjusted with grease gun.
Number of track rollers (each side) 8
Type of shoes (standard) Single grouser
Number of shoes (each side) 46
Grouser height 2.3" 57.5 mm
Shoe width (standard 24" 600 mm
Ground contact area 4,836 in² 31200 cm²
Ground pressure
(with dozer, ROPS canopy):
8.08 psi 55.7 kPa
0.57 kgf/cm²
Track gauge 6'3" 1900 mm
Length of track on ground 10'5" 3161 mm
SERVICE REFILL CAPACITIES
Coolant 11.9 U.S. gal 45 ltr
Fuel tank 98.3 U.S. gal 372 ltr
Engine oil 7.2 U.S. gal 27 ltr
Hydraulic tank 26.7 U.S. gal 101 ltr
Final drive (each side) 2.2 U.S. gal 8.1 ltr
Operating Weight (approximate)
Tractor weight Including ROPS cab, U frame for power angle tilt dozer, rated capacity of lubricant, coolant, full fuel tank, operator, and standard equipment.
D61EX-23 36,999 lb 16780 kg
Operating weight: Including Power Angle Tilt dozer, ROPS cab, operator, standard equipment, rated capacity of lubricant, hydraulic control unit, coolant, and full fuel tank.
D61EX-23 39,099 lb 17735 kg
HYDRALIC SYSTEM
Closed-center Load Sensing System (CLSS) designed for precise and responsive control, and for efficient simultaneous operation.
Hydraulic control unit:
All spool control valves externally mounted remote to the hydraulic tank. Piston-type hydraulic pump with capacity (discharge flow) of 171 ltr/min / 45 U.S. gal/min at rated engine rpm.
Relief valve setting 3,974 psi 280 kg/cm²
27.4MPa
Hydraulic cylinders 3,974
Hydraulic cylinders: Number of cylinders Bore
Blade lift 2 4"
100 mm
Blade tilt 1 5"
120 mm
Blade angle 2 4"
100 mm
Hydraulic oil capacity (refilling):
Power angle tilt dozer 26.7 U.S. gal 101 ltr
Control valves:
3-spool control valve for Power Angle Tilt dozer
Positions:
Blade lift Raise, hold, lower, and float
Blade tilt Right, hold, and left
Blade angle Right, hold, and left
Additional control valve required for ripper
Positions:
Ripper lift Raise, hold, and lower

Komatsu Dozers D51EXi-22
D51EXi-22 Crawler Dozer

iMC (intelligent machine control) machines have the following advantages over dozers with external grade control systems.

Innovative
Automated operation from rough dozing to finish grade.

Intelligent
New dozing mode, load control performance features.

Integrated
Standard factory installed integrated system.

No Cables
No coiled cables between machine and blade.

No Climbing
GNSS antenna and mast removed from blade.

No Connections
No daily connections required between machine and blade.

Engine
Model Komatsu SAA6D107E-1*
Type 4-cycle, water-cooled, direct injection
Aspiration Turbocharged, air-to-air aftercooled
Number of cylinders 6
Bore x stroke 4.21" x 4.88" 107 mm x 124 mm
Piston displacement 408 in³ 6.69 ltr
Governor All-speed, electronic
Horsepower
SAE J1995 - Gross 133 HP 99 kW
ISO 9249 / SAE J1349 - Net 130 HP 97 kW
Rated rpm 2200 rpm
Fan drive type Hydraulic(reversible)
Lubrication system:
Method Gear pump, force lubrication
Filter Full-flow
*EPA Tier 3 emissions certified
Hydrostatic transmission
Dual-path, hydrostatic transmission provides infinite speed changes up to 9.0 km/h 5.6 mph. The variable capacity travel motors allow the operator to select the optimum speed to match specific jobs. Travel control lock lever and neutral switch.
Travel speed
(quick shift mode)
Forward Reverse
1st 0–2.1 mph
0–3.4 km/h
0–2.5 mph
0–4.1 km/h
2nd 0–3.5 mph
0–5.6 km/h
0–4.0 mph
0–6.5 km/h
3rd 0–5.6 mph
0–9.0 km/h
0–5.6 mph
0–9.0 km/h
Travel speed (variable mode) Forward Reverse
0–5.6 mph
0–9.0 km/h
0–5.6 mph
0–9.0 km/h
FINAL DRIVE
Two-stage planetary gear integrated into axial piston travel motors. Compact in-shoe mount reduces risk of damage by debris. Bolt-on sprocket segments for easy replacement.
STEERING SYSTEM
Palm Command Control System (PCCS) joystick control for all directional movements. Pushing the joystick forward results in forward machine travel, while pulling it rearward reverses the machine. Simply tilt the joystick to the left or right to make a turn. Tilting the joystick fully to the left or right activates counter-rotation. Hydrostatic Transmission (HST) eliminates steering clutches and brakes, providing smooth powerful turns. Fully electronic control enables smooth control. The PCCS utilizes shift buttons to increase and decrease speed.

 

Minimum turning radius* 7'10" 2.39 m
As measured by track marks on the ground at pivot turn.

 

Undercarriage
Suspension Oscillating equalizer bar and pivot shaft
Track roller frame Monocoque, large section, durable construction
Rollers and idlers Lubricated track rollers
Lubricated tracks: Unique seals help prevent entry of foreign abrasive material into pin to bushing clearances for long service life.
Parallel Link Undercarriage System (PLUS) Increased component size and strength, and rotating bushing design provide extended wear life and lower maintenance.
Number of track rollers (each side) 7
Type of shoes (standard) Single grouser PLUS
Number of shoes (each side) 44
Grouser height 2.2" 56 mm
Shoe width (standard) 22" 560 mm
Ground contact area 4,752 in² 30643 cm²
Ground pressure
(with dozer, ROPS cab)
5.76 psi 0.41 kgf/cm² / 39.7 kPa
Track gauge 5'10" 1790 mm
Length of track on ground 9'0" 2736 mm
SERVICE REFILL CAPACITIES
Coolant 9.3 U.S. gal 35 ltr
Fuel tank 71.3 U.S. gal 270 ltr
Engine oil 5.3 U.S. gal 20 ltr
Hydraulic tank 16.6 U.S. gal 63 ltr
Final drive (each side) 1.1 U.S. ga 4.0 ltr
Operating Weight
Tractor weight: Including ROPS cab, rated capacity of lubricant, coolant, full fuel tank, operator, and standard equipment.
D51EX-22 24,074 lb 10920 kg
Operating weight: Including power angle tilt dozer, ROPS cab, operator, standard equipment, rated capacity of lubricant, coolant, and full fuel tank.
D51EX-22 27,381 lb 12420 kg
hydraulic system
Closed-center Load Sensing System (CLSS) designed for precise and responsive control and for efficient simultaneous operation.
Hydraulic control unit:
All spool control valves externally mounted remote to the hydraulic tank. Piston-type hydraulic pump with capacity (discharge flow) of 99 ltr/min 26.2 U.S. gal/min at rated engine rpm.
Relief valve setting 3,983 psi 27.4 MPa / 280 kg/cm²
Hydraulic cylinders   Double-acting, piston type
Number of cylinders: Bore Bore
Blade lift / 2 3.54" 90 mm
Blade tilt / 1 3.94" 100 mm
Blade angle / 2 3.54" 90 mm
Hydraulic oil capacity (refilling):  
Power angle tilt dozer 16.6 U.S. gal l 63 ltr
Control valves:
3-spool control valve for power angle tilt dozer.
Positions:
Blade lift Raise, hold, lower, and float
Blade tilt   Right, hold, and left
Blade angle   Right, hold, and left
Additional control valve required for ripper
Positions:
Ripper lift  Raise, hold, and lower

Comments are closed.

Save Hundreds on Your Rentals

Fill out our form - takes 30 seconds - Enjoy Competing Quotes

Web Analytics