Save Hundreds on Your Rentals

Fill out our form - takes 30 seconds - Enjoy Competing Quotes

Construction Equipment Rental in Hilo, Hawaii

We cater to do-it-yourselfers, local contractors, and large scale enterprises operating in residential and commercial construction industries. Whether you need just one or two dozers or excavators at the jobsite in Hilo or you need an entire fleet of heavy machinery for an ongoing project, our vendors would be able to meet all of your requirements.

While you may have planned everything much in advance, it is possible that you need to opt for heavy construction equipment rental in Hilo at the last minute. Even on these occasions, we’d be able to put you in touch with vendors who can provide necessary construction equipment and even transport it to your premises or the jobsite within few hours or a day at most.

Contact us today! You can dial the toll free number or contact us by submitting the contact form on the right. We will get back to you ASAP.

Equipment Rental Hilo, Construction equipment rental Hilo, Construction Hilo, Heavy Equipment Rental Hilo.

Komatsu Dozers D65WX-17 WH

D65WX-17 WH Waste Handling Dozer

Engine
Model Komatsu SAA6D114E-5*
Type 4-cycle, water-cooled, direct injection
Aspiration Komatsu variable geometry Turbocharged, air-to-air aftercooled
Number of cylinders 6
Bore x stroke 4.49" x 5.69" 114 mm x 144.5 mm
Piston displacement 540 in³ 8.85 ltr
Governor All-speed and mid-range, electronic
Horsepower
SAE J1995 - Gross 207 HP 155 kW
(ISO 14396 205 HP 153 kW
ISO 9249 / SAE J1349 - Net 186 HP 139 kW
Rated rpm 1950 rpm
Fan drive type Hydraulic
Lubrication system:
Method Gear pump, force lubricationn
Filter Full-flow
*EPA Tier 4 Interim and EU stage 3B emissions certified
TORQFLOW transmission
Komatsu TORQFLOW transmission consists of a water-cooled, 3-element, 1-stage, 2-phase, torque converter with lockup clutch, and a planetary gear, multiple-disc clutch transmission which is electronically controlled, hydraulically actuated and force-lubricated for optimum heat dissipation. Shift lock lever and neutral safety switch.
Travel speed Forward Reverse
1st 2.2 mph
3.6 km/h
2.7 mph
4.4 km/h
2nd 3.4 mph
5.5 km/h
4.1 mph
6.6 km/h
3rdL 4.5 mph
7.2 km/h
5.3 mph
8.6 km/h
3rd 7.0 mph
11.2 km/h
8.3 mph
13.4 km/h
STEERING SYSTEM
Palm Command Control System (PCCS) lever controls for all directional movements. Pushing the PCCS lever forward results in forward machine travel, while pulling it rearward reverses the machine. Simply tilt the PCCS lever to left to make a left turn. Tilt it to the right for a right turn.
Hydrostatic Steering System (HSS) is powered by steering planetary units and a hydraulic pump and motor. Counter-rotation turns are also available. Wet, multiple-disc, pedal-controlled service brakes are spring-actuated and hydraulically released. Gear shift lock lever also applies parking brake.
Minimum turning radius:
D65EX-17 6'3" 1.9 m
D65EX-17 with PAT 6'7" 2.0 m
D65PX-17 7'3" 2.2 m
D65WX-17 6'11" 2.1 m
Undercarriage
Suspension Oscillating-type with equalizer bar and pivot shafts
Track roller frame Monocoque, large section, durable construction
Rollers and idlers Lubricated
Track shoes Parallel Link Undercarriage System (PLUS) with lubricated rotating bushings for extended system wear life and lower maintenance costs. Track tension is easily adjusted with grease gun.
FINAL DRIVE
Double-reduction final drive of spur and planetary gear sets to increase tractive effort and reduce gear tooth stresses for long final drive life. Segmented sprocket teeth are bolt-on for easy replacement.
HYDRAuLIC SYSTEM
Closed-center load sensing system (CLSS) designed for precise and responsive control, and for efficient simultaneous operation.

Hydraulic control units:
All spool valves externally mounted beside the hydraulic tank. Piston type hydraulic pump with capacity (discharge flow) of 248 ltr/min / 65.5 U.S. gal/min at rated engine rpm.

Relief valve setting 4,050 psi 27.9 MPa / 285 kg/cm²
Control valves:
Spool control valves for SIGMADOZER or straight tilt dozer
Positions:
Blade lift Raise, hold, lower, and float
Blade tilt Right, hold, and left
Rear attachment Raise, hold, and lower
Spool control valves for Power Angle Tilt dozer
Positions:
Blade lift Raise, hold, lower, and float
Blade tilt Right, hold, and left
Blade angle Right, hold, and left
Rear attachment Raise, hold, and lower
Hydraulic cylinders Double-acting, piston
Number of cylinders - SIGMADOZER Straight Tilt Dozer: Bore:
Blade lift - 2 3.3" 85 mm
Blade tilt - 1 4.9" 125 mm
Blade angle - 2 N/A
Ripper lift - 1 4.9" 125 mm
Pitch angle - 1 39° - 53°
Number of cylinders - Power Tilt Dozer: Bore:
Blade lift - 2 3.5" 90 mm
Blade tilt - 1 5.1" 130 mm
Blade angle - 2 4.3" 110mm
Ripper lift - 1 4.9" 125 mm
Pitch angle - 1 52° - 58°
Hydraulic oil capacity (refill): 14.5 U.S. ga 55 ltr
Ripper equipment (additional volume):
Multi-shank ripper 1.8 U.S. ga 7 ltr
SERVICE REFILL CAPACITIES
Fuel tank 109.6 U.S. gal 415 ltr
Coolant 14.3 U.S. gal 54 ltr
Engine 6.6 U.S. gal 25 ltr
Torque converter, transmission, bevel gear, and steering system 12.7 U.S. gal 48 ltr
Final drive (each side):
D65EX-17 4.4 U.S. gal 16.5 ltr
D65EX-17 with PAT 4.4 U.S. gal 16.5 ltr
D65PX-17 5.8 U.S. gal 22 ltr
D65WX-17 5.8 U.S. gal 22 ltr

Komatsu Dozers D475A-5
D475A-5 Crawler Dozer

When mines are looking for a dozer with the versatility to go from stripping overburden one day to ripping solid rock or stirring the leech field the next and cleaning up around the dragline the day after they call on the D475A-5. Utilizing an automatic lock-up torque converter, the D475A-5 give the operator a great combination of power and speed and both of those equal production. Low drive undercarriage with K-bogies make the D475A-5 a superior ripping tractor. Palm control joysticks, air suspension seat that rotates 15 degrees to the right and low dBA cab provide the operator with a comfortable environment with the tools he needs to maximize production.

Engine
Model Komatsu SAA12V140E-3
Type 4-cycle, water-cooled, direct injection
Aspiration Turbocharged, air-to-air aftercooled
Number of cylinders 12
Bore x stroke 5.51" x 6.50" 140 mm x 165 mm
Piston displacement 1,860 in³ 30.48 ltr
Flywheel horsepower:
SAE J1349 899 HP 671 kW
DIN6270 890 HP 644 kW
Hydraulic fan at maximum speed 860 HP 641 kW
Rated rpm 1900 rpm
Governor All-speed, electronic
Lubrication system:
Method Gear pump, force lubrication
Filter Full-flow and bypass combined
TORQFLOW Transmission
Komatsu TORQFLOW transmission consists of a water-cooled, 3-element, 1-stage, 1-phase torque converter with lockup clutch and a planetary gear, multiple-disc clutch transmission which is hydraulically actuated and force-lubricated for optimum heat dissipation. Gearshift lock lever and neutral safety switch help prevent accidental starts.
Gear Forward Reverse
1st 2.1 mph 3.3 km/h 2.6 mph 4.2 km/h
2nd 3.9 mph 6.2 km/h 5.0 mph 8.0 km/h
3rd 7.0 mph 11.2 km/h 8.7 mph 14.0 km/h
Final Drive
Double-reduction final drive of spur and planetary gear sets to increase tractive effort and reduce gear tooth stresses for long final drive life. Segmented sprocket teeth are bolt-on for easy replacement.
Steering System
PCCS, joystick controlled, wet multiple-disc steering clutches are spring-loaded and hydraulically released.Wet multiple-disc, pedal/lever controlled steering brakes are spring-actuated hydraulically released and require no adjustment. Steering clutches and brakes are interconnected for easy, responsive steering.
Minimum turning radius 15'1" 4.6 m
Undercarriage
Suspension Oscillating equalizer bar and pivot shaft
Track roller frame Cylindrical, high-tensile-strength steel construction
Rollers and idlers Lubricated track rollers
K-Bogie undercarriage Lubricated track rollers are resiliently mounted to the track frame with a bogie suspension system whose oscillating motion is cushioned by rubber pads.
Extreme service track shoes Lubricated tracks. Unique seals prevent entry of foreign abrasives into pin-to-bushing clearances to provide extended service life. Track tension is easily adjusted with grease gun.
Number of shoes (each side) 41
Grouser height:
Single grouser 4.1" 105 mm
Shoe width (standard) 32" 810 mm
Ground contact area 11,360 in² 73290 cm²
Ground pressure (Tractor) 16.2 psi 112 kPa 1.14 kg/cm²
Number of track rollers 8
Number of carrier rollers 2
Extreme service shoes: 36" 910 mm
Additional weight 4,030 lb 1830 kg
Ground contact area 12,762 in² 82340 cm²
Tractor ground pressure 14.8 psi 102 kPa 1.04 kg/cm²
Service Refill Capacities
Fuel tank 441 U.S. gal 1670 ltr
Coolant 72.6 U.S. gal 275 ltr
Engine 32.0 U.S. gal 121 ltr
Torque converter, transmission, bevel gear, and steering system 55.5 U.S. gal 210 ltr
Final drive (each side) 19.8 U.S. gal 75 ltr
Operating Weight
Tractor weight
Including rated capacity of lubricant, coolant, full fuel tank, operator, and standard equipment.
184,290 lb 83590 kg
Operating weight
Including strengthened Full-U tilt dozer, giant ripper, steel cab, ROPS, operator, standard equipment, rated capacity of lubricant, coolant, and full fuel tank.
238,960 lb 108390 kg
Ground pressure 24.0 psi 166 kPa 1.69 kg/cm²
Hydraulic System
Closed-center load sensing system (CLSS) designed for precise and responsive control, and for efficient simultaneous operation.
Relief valve setting 3,980 psi 27.5 MPa 280 kg/cm²
Control valves (Spool control valves for Semi-U tilt dozer and Full-U tilt dozer):
Positions:
Blade lift Raise, hold, lower, and float
Blade tilt Right, hold, and left
Control valves (Spool control valves for variable digging angle multi-shank ripper and giant ripper.
Positions:
Ripper lift Raise, hold, and lower
Ripper tilt Increase, hold, and decrease
Hydraulic cylinders Double-acting, piston
Hydraulic cylinders
Number of cylinders
Bore Bore
Blade lift / 2 7.09" 180 mm
Blade tilt / 1 9.84" 250 mm
Ripper lift / 2 8.86" 225 mm
Ripper tilt / 2 8.86" 225 mm
Hydraulic oil capacity (refill):
Semi-U tilt dozer 48 U.S. gal 180 ltr
U tilt dozer 48 U.S. gal 180 ltr
Ripper equipment (additional volume):
Giant ripper 34 U.S. gal 130 ltr
Multi-shank ripper 34 U.S. gal 130 ltr

Komatsu Dozers D37EX-23

D37EX-23 Crawler Dozer

Komatsu small dozers are great finish grading tractors for a lot of reasons but the most obvious is the super slant nose design. The super slant nose design moves the coolers and hydraulic fan to the rear and the operator forward to create a balance that makes fine grading with or without a grade control system a breeze. A fully hydrostatic drivetrain gives the operator incredibly quick and precise maneuverability. And new Power and Economy working modes allow the operator to adjust his machine's performance to his current job and save on fuel consumption as he's doing it. Like all Komatsu products, the D37EX-23 has the advanced hydraulics to make the addition of a grade control system seamless and turn it from a great grading tractor to an incredibly precise and fast fine grading system.

Engine
Model Komatsu SAA4D95LE-6*
Type 4-cycle, water-cooled, direct injection
Aspiration Variable flow, turbocharged, air-to-air aftercooled
Number of cylinders 4
Bore x stroke 3.75" x 4.52" 95 mm x 115 mm
Piston displacement 199 in³ 3.26 ltr
Governor All-speed, electronic
Horsepower
SAE J1995 - Gross 91 HP 68 kW
(ISO 14396 89 HP 66 kW
ISO 9249 / SAE J1349 - Net 79 HP 59 kW
Rated rpm 2200 rpm
Fan drive type Hydraulic
Lubrication system:
Method Gear pump, force lubricationn
Filter Full-flow
Hydrostatic transmission
Dual-path, hydrostatic transmission provides infinite speed changes up to 5.3 km/h / 8.5 mph. The variable capacity travel motors allow the operator to select the optimum speed to match specific jobs. Travel control lock lever and neutral switch.
Travel speed (quick shift mode)* Forward Reverse
1st 0–2.1 mph
0–3.4 km/h
0–2.5 mph
0–4.1 km/h
2nd 0–3.5 mph
0–5.6 km/h
0–4.0 mph
0–6.5 km/h
3rd 0–5.3 mph
0–8.5 km/h
0–5.3 mph
0–8.5 km/h
Travel speed (variable mode) Forward Reverse
*Quick shift speeds are adjustable in the monitor.
FINAL DRIVE
In-shoe mounted axial piston type travel motors with integrated two stage planetary gear reduction. Compact in-shoe mount reduces risk of damaged by debris. Bolt-on sprocket ring.
STEERING SYSTEM
Palm Command Control System (PCCS) joystick control for all directional movements. Pushing the joystick forward results in forward machine travel, while pulling it rearward reverses the machine. Simply tilt the joystick to the left or right to make a turn. Tilting the joystick fully to the left or right activates counter-rotation.Hydrostatic Transmission (HST) provides smooth powerful turns. Fully electronic control enables smooth control that can be adjusted in the monitor. The PCCS utilizes shift buttons to increase and decrease speed.
Minimum turning radius* 79" 2.0 m
*As measured by track marks on the ground at pivot turn.
Undercarriage
Suspension Rigid track frame
Track roller frame Monocoque, large section, durable construction
Rollers and idlers Lubricated track rollers
Lubricated tracks Unique seals minimize the entry of foreign abrasive material into pin to bushing clearances to provide extended service life. Track tension is easily adjusted with a grease gun.
Sealed and lubricated track Track tension is easily adjusted with grease gun.
Tractor for inside mounted blade (PAT)
Number of track rollers (each side) 6
Number of carrier rollers (each side) 1
Type of shoes (standard) Single grouser
Number of shoes (each side) 41
Grouser height 1.9" 47 mm
Shoe width (standard) 18" 460 mm
Ground contact area 2,778 in² 17920 cm²
Ground pressure
(with standard shoe)
6.39 psi 0.45 kgf/cm² / 44.1 kPa
Track gauge 5'2" 1570 mm
Length of track on ground 7'4" 2230 mm
Link pitch 6.1" 154 mm
SERVICE REFILL CAPACITIES
Coolant 9.0 U.S. gal 34 ltr
Fuel tank 50.2 U.S. gal 190 ltr
Engine oil 2.9 U.S. gal 11 ltr
Hydraulic tank 16.9 U.S. gal 64 ltr
Final drive (each side) 0.9 U.S. gal 3.5 ltr
Operating Weight (approximate)
Tractor weight: Including ROPS cab, U frame for power angle tilt dozer, rated capacity of lubricant, coolant, full fuel tank, operator, and standard equipment. 16,314 lb 7400 kg
Operating weight: Operating weight: Including power angle tilt dozer, ROPS cab, operator, standard equipment, rated capacity of lubricant, coolant, and full fuel tank. 18,695 lb 8480 kg
HYDRALIC SYSTEM
Closed-center Load Sensing System (CLSS) designed for precise and responsive control, and for efficient simultaneous operation.
Hydraulic control unit:
All spool control valves externally mounted remote to the hydraulic tank. Piston-type hydraulic pump with capacity (discharge flow) of 99 ltr/min / 26 U.S. gal/min at rated engine rpm.
Relief valve setting 3,974 psi 27.4 MPa / 280 kg/cm²
Hydraulic cylinders Double-acting, piston type
Number of cylinders: Bore Bore
Blade lift / 2 3.0" 75 mm
Blade tilt / 1 3.5" 90 mm
Blade angle / 2 3.1" 4"
80 mm
Hydraulic oil capacity (refilling):
Power angle tilt dozer 15.9 U.S. gal 60 ltr
Control valves:
3-spool control valve for power angle tilt dozer.
Positions:
Blade lift Raise, hold, lower, and float
Blade tilt Right, hold, and left
Blade angle Right, hold, and left
Additional control valve required for ripper
Positions:
Ripper lift Raise, hold, and lower

Comments are closed.

Save Hundreds on Your Rentals

Fill out our form - takes 30 seconds - Enjoy Competing Quotes

Web Analytics