Save Hundreds on Your Rentals

Fill out our form - takes 30 seconds - Enjoy Competing Quotes

Equipment Rental in Bella Vista, California

When you need machinery and need it real quick to keep your construction project on track,you cannot of course buy heavy construction equipment outright. In such cases,it makes perfect sense to go with a construction equipment rental in Bella Vista, California

Yes, you can have heavy construction equipment at your disposal,right from dozers and excavators to forklifts and everything else on a job-to-job basis.

There is no capital investment involved and it is possible to get started in as little as a day or two no matter where you are in California. We have a network of construction equipment vendors in Bella Vista, California and that supply of the smallest and largest of construction equipment.

Getting started is easy. You can dial our toll free number right away and learn more about how this rental service works. You can also fill out the contact form and we will get back to you in no time.

Equipment Rental Bella Vista, Construction equipment rental Bella Vista, Construction rental Bella Vista, Heavy Equipment Bella Vista.

Komatsu Dozers D37EXi-23

D37EXi-23 Crawler Dozer

iMC (intelligent machine control) machines have the following advantages over dozers with external grade control systems.

Innovative
Automated operation from rough dozing to finish grade.

Intelligent
New dozing mode, load control performance features.

Integrated
Standard factory installed integrated system.

No Cables
No coiled cables between machine and blade.

No Climbing
GNSS antenna and mast removed from blade.

No Connections
No daily connections required between machine and blade.

Engine
Model Komatsu SAA4D95LE-6*
Type 4-cycle, water-cooled, direct injection
Aspiration Variable flow, turbocharged, air-to-air aftercooled
Number of cylinders 4
Bore x stroke 3.75" x 4.52" 95 mm x 115 mm
Piston displacement 199 in³ 3.26 ltr
Governor All-speed, electronic
Horsepower
SAE J1995 - Gross 91 HP 68 kW
(ISO 14396 89 HP 66 kW
ISO 9249 / SAE J1349 - Net 79 HP 59 kW
Rated rpm 2200 rpm
Fan drive type Hydraulic
Lubrication system:
Method Gear pump, force lubricationn
Filter Full-flow
Hydrostatic transmission
Dual-path, hydrostatic transmission provides infinite speed changes up to 5.3 km/h / 8.5 mph. The variable capacity travel motors allow the operator to select the optimum speed to match specific jobs. Travel control lock lever and neutral switch.
Travel speed (quick shift mode)* Forward Reverse
1st 0–2.1 mph
0–3.4 km/h
0–2.5 mph
0–4.1 km/h
2nd 0–3.5 mph
0–5.6 km/h
0–4.0 mph
0–6.5 km/h
3rd 0–5.3 mph
0–8.5 km/h
0–5.3 mph
0–8.5 km/h
Travel speed (variable mode) Forward Reverse
0–5.3 mph
0–8.5 km/h
0–5.3 mph
0–8.5 km/h
*Quick shift speeds are adjustable in the monitor.
FINAL DRIVE
In-shoe mounted axial piston type travel motors with integrated two stage planetary gear reduction. Compact in-shoe mount reduces risk of damaged by debris. Bolt-on sprocket ring.
STEERING SYSTEM
Steering System Palm Command Control System (PCCS) joystick control for all directional movements. Pushing the joystick forward results in forward machine travel, while pulling it rearward reverses the machine. Simply tilt the joystick to the left or right to make a turn. Tilting the joystick fully to the left or right activates counter-rotation.

Hydrostatic Transmission (HST) provides smooth powerful turns. Fully electronic control enables smooth control that can be adjusted in the monitor. The PCCS utilizes shift buttons to increase and decrease speed.

Minimum turning radius: 87" 2.2 m
As measured by track marks on the ground at pivot turn.
Undercarriage
Suspension Rigid track frame
Track roller frame Monocoque, large section, durable construction
Rollers and idlers Lubricated track rollers
Sealed and lubricated track Track tension is easily adjusted with grease gun.
Tractor for inside mounted blade (PAT)
Number of track rollers (each side) 6
Number of carrier rollers (each side) 1
Type of shoes (standard) Single grouser
Number of shoes (each side) 41
Grouser height 1.9" 47 mm
Shoe width (standard) 18" 460 mm
Ground contact area 3,180 in² 20516 cm²
Ground pressure
(with standard shoe)
5.93 psi 0.42 kgf/cm² / 40.9 kPa
Track gauge 5'2" 1570 mm
Length of track on ground 7'4" 2230 mm
Link pitch 6.1" 154 mm
SERVICE REFILL CAPACITIES
Coolant 9.0 U.S. gal 34 ltr
Fuel tank 50.2 U.S. gal 190 ltr
Engine oil 2.9 U.S. gal 11 ltr
Hydraulic tank 16.9 U.S. gal 64 ltr
Final drive (each side) 0.9 U.S. gal 3.5 ltr
Operating Weight (approximate)
Tractor weight: Including ROPS cab, U frame for power angle tilt dozer, rated capacity of lubricant, coolant, full fuel tank, operator, and standard equipment.
ROPS cab 18,387 lb 8340 kg
Operating weight: Including Power Angle Tilt dozer, ROPS cab, operator, standard equipment, rated capacity of lubricant, hydraulic control unit, coolant, and full fuel tank.
ROPS cab 20,922 lb 9490 kg
HYDRALIC SYSTEM
Closed-center Load Sensing System (CLSS) designed for precise and responsive control, and for efficient simultaneous operation.
Hydraulic control unit:
All spool control valves externally mounted remote to the hydraulic tank. Piston-type hydraulic pump with capacity (discharge flow) of 99 ltr/min 26 U.S. gal/min at rated engine rpm.
Relief valve setting 3,974 psi 27.4 MPa / 280 kg/cm²
Hydraulic cylinders Double-acting, piston type
Number of cylinders: Bore Bore
Blade lift / 2 3" 75 mm
Blade tilt / 1 3.5" 90 mm
Blade angle / 2 3.1" 80 mm
Hydraulic oil capacity (refill):
Power angle tilt dozer 15.9 U.S. gal 60 ltr
Control valves:
3-spool control valve for Power Angle Tilt dozer
Positions:
Blade lift Raise, hold, lower, and float
Blade tilt Right, hold, and left
Blade angle Right, hold, and left
Additional control valve required for ripper
Positions:
Ripper lift Raise, hold and lower

Komatsu Wheel Loaders WA270-7
WA270-7 Wheel Loader

The Komatsu Tier 4 interim technology on the WA270-7 is designed to keep the operator working rather than having to stop and regenerate while saving up to 10% on fuel burned. The hydrostatic drive system on the WA270-7 gives the operator quick and powerful response, self-braking effect of dynamic braking and traction control. A multi-function mono-lever, rearview camera system with separate screen and heated, air ride suspension seat give the operator a comfortable and ergonomic work environment.

Engine
Model Komatsu SAA6D107E-2*
Type Water-cooled, 4-cycle
Aspiration Turbo-charged, after-cooled, cooled EGR
Number of cylinders 6
Bore x stroke 4.21" x 4.88" 107 mm x 124 mm
Piston displacement 408 in³ 6.69 ltr
Governor All-speed, electronic
Horsepower:
Gross - SAE J1995 153 HP 115 kW
Net - ISO 9249/SAE J1349 149 HP 111 kW 149 HP
Rated rpm 2000 rpm
Max power - ISO 14396 @ 1900 rpm 150 HP 112 kW
Fan drive method for radiator cooling Hydraulic
Fuel system Direct injection
Lubrication system:
Method Gear pump, force-lubrication
Filter Full-flow type
Air cleaner Dry type with double elements and dust evacuator, plus dust indicator
*EPA Tier 4 Interim and EU stage 3B emissions certified
Transmission
Transmission Hydrostatic, 1 pump, 2 motors with speed range select
Travel speed Forward Reverse
1st 0.6 - 8.1 mph 0.6 - 8.1 mph
2nd 8.1 mph 8.1 mph
3rd 11.8 mph 11.8 mph
4th 23.6 mph 23.6 mph
Measured with 20.5-25 tires
Axles and Final Drives
Drive system Four-wheel drive
Front Fixed, semi-floating
Rear Center-pin support, semi-floating, 20° total oscillation
Reduction gear Spiral bevel gear
Differential gear Torque proportioning
Final reduction gear Planetary gear, single reduction
Brakes
Service brakes Hydraulically-actuated, wet disc brakes actuate on four wheels.
Parking brake Wet, multi-disc brake on transfer output shaft.
Emergency brake Parking brake is commonly used
Steering System
Type Articulated type, fully-hydraulic power steering
Steering angle 38° each direction (40° to max end stop)
Minimum turning radius at the center of outside tire 17' 0" 5175 mm
Hydraulic System
Steering system:
Hydraulic pump Piston pump, in common with loader control
Capacity (at rated rpm) 39.6 U.S. gal/min 150 ltr/min
Relief valve setting 3,000 psi 20.6 MPa 210 kgf/cm²
Hydraulic cylinders:
Type Double-acting, piston type
Number of cylinders 2
Bore x stroke 2.76" x 17.8" 70 mm x 453 mm
Loader control:
Hydraulic pump Piston pump, in common with steering system
Capacity (at rated rpm) 39.6 U.S. gal/min 150 ltr/min
Relief valve setting 4,555 psi 320 kg/cm² 31.4 MPa
Hydraulic cylinders:
Type Double-acting, piston type
Number of cylinders bore x stroke: bore x stroke:
Boom cylinder / 2 4.3" x 28.2" 110 mm x 717 mm
Bucket cylinder / 1 5.5" x 18.9" 140 mm x 480 mm
Control valve 2-spool type
Control positions:
Boom Raise, hold, lower, and float
Bucket Tilt-back, hold, and dump
Hydraulic cycle time (rated load in bucket):
Raise 5.7 sec
Dump 2.0 sec
Lower (Empty) 3.2 sec
Service Refill Capacities
Cooling system 7.4 U.S. gal 28 ltr
Fuel tank 49.1 U.S. gal 186 ltr
Engine 6.7 U.S. gal 23 ltr
Hydraulic system 20.6 U.S. gal 78 ltr
Axle front 4.9 U.S. gal 18.5 ltr
Axle rear 4.8 U.S. gal 18 ltr
Transfer 2.1 U.S. gal 7 ltr

Komatsu Dozers D475A-5
D475A-5 Crawler Dozer

When mines are looking for a dozer with the versatility to go from stripping overburden one day to ripping solid rock or stirring the leech field the next and cleaning up around the dragline the day after they call on the D475A-5. Utilizing an automatic lock-up torque converter, the D475A-5 give the operator a great combination of power and speed and both of those equal production. Low drive undercarriage with K-bogies make the D475A-5 a superior ripping tractor. Palm control joysticks, air suspension seat that rotates 15 degrees to the right and low dBA cab provide the operator with a comfortable environment with the tools he needs to maximize production.

Engine
Model Komatsu SAA12V140E-3
Type 4-cycle, water-cooled, direct injection
Aspiration Turbocharged, air-to-air aftercooled
Number of cylinders 12
Bore x stroke 5.51" x 6.50" 140 mm x 165 mm
Piston displacement 1,860 in³ 30.48 ltr
Flywheel horsepower:
SAE J1349 899 HP 671 kW
DIN6270 890 HP 644 kW
Hydraulic fan at maximum speed 860 HP 641 kW
Rated rpm 1900 rpm
Governor All-speed, electronic
Lubrication system:
Method Gear pump, force lubrication
Filter Full-flow and bypass combined
TORQFLOW Transmission
Komatsu TORQFLOW transmission consists of a water-cooled, 3-element, 1-stage, 1-phase torque converter with lockup clutch and a planetary gear, multiple-disc clutch transmission which is hydraulically actuated and force-lubricated for optimum heat dissipation. Gearshift lock lever and neutral safety switch help prevent accidental starts.
Gear Forward Reverse
1st 2.1 mph 3.3 km/h 2.6 mph 4.2 km/h
2nd 3.9 mph 6.2 km/h 5.0 mph 8.0 km/h
3rd 7.0 mph 11.2 km/h 8.7 mph 14.0 km/h
Final Drive
Double-reduction final drive of spur and planetary gear sets to increase tractive effort and reduce gear tooth stresses for long final drive life. Segmented sprocket teeth are bolt-on for easy replacement.
Steering System
PCCS, joystick controlled, wet multiple-disc steering clutches are spring-loaded and hydraulically released.Wet multiple-disc, pedal/lever controlled steering brakes are spring-actuated hydraulically released and require no adjustment. Steering clutches and brakes are interconnected for easy, responsive steering.
Minimum turning radius 15'1" 4.6 m
Undercarriage
Suspension Oscillating equalizer bar and pivot shaft
Track roller frame Cylindrical, high-tensile-strength steel construction
Rollers and idlers Lubricated track rollers
K-Bogie undercarriage Lubricated track rollers are resiliently mounted to the track frame with a bogie suspension system whose oscillating motion is cushioned by rubber pads.
Extreme service track shoes Lubricated tracks. Unique seals prevent entry of foreign abrasives into pin-to-bushing clearances to provide extended service life. Track tension is easily adjusted with grease gun.
Number of shoes (each side) 41
Grouser height:
Single grouser 4.1" 105 mm
Shoe width (standard) 32" 810 mm
Ground contact area 11,360 in² 73290 cm²
Ground pressure (Tractor) 16.2 psi 112 kPa 1.14 kg/cm²
Number of track rollers 8
Number of carrier rollers 2
Extreme service shoes: 36" 910 mm
Additional weight 4,030 lb 1830 kg
Ground contact area 12,762 in² 82340 cm²
Tractor ground pressure 14.8 psi 102 kPa 1.04 kg/cm²
Service Refill Capacities
Fuel tank 441 U.S. gal 1670 ltr
Coolant 72.6 U.S. gal 275 ltr
Engine 32.0 U.S. gal 121 ltr
Torque converter, transmission, bevel gear, and steering system 55.5 U.S. gal 210 ltr
Final drive (each side) 19.8 U.S. gal 75 ltr
Operating Weight
Tractor weight
Including rated capacity of lubricant, coolant, full fuel tank, operator, and standard equipment.
184,290 lb 83590 kg
Operating weight
Including strengthened Full-U tilt dozer, giant ripper, steel cab, ROPS, operator, standard equipment, rated capacity of lubricant, coolant, and full fuel tank.
238,960 lb 108390 kg
Ground pressure 24.0 psi 166 kPa 1.69 kg/cm²
Hydraulic System
Closed-center load sensing system (CLSS) designed for precise and responsive control, and for efficient simultaneous operation.
Relief valve setting 3,980 psi 27.5 MPa 280 kg/cm²
Control valves (Spool control valves for Semi-U tilt dozer and Full-U tilt dozer):
Positions:
Blade lift Raise, hold, lower, and float
Blade tilt Right, hold, and left
Control valves (Spool control valves for variable digging angle multi-shank ripper and giant ripper.
Positions:
Ripper lift Raise, hold, and lower
Ripper tilt Increase, hold, and decrease
Hydraulic cylinders Double-acting, piston
Hydraulic cylinders
Number of cylinders
Bore Bore
Blade lift / 2 7.09" 180 mm
Blade tilt / 1 9.84" 250 mm
Ripper lift / 2 8.86" 225 mm
Ripper tilt / 2 8.86" 225 mm
Hydraulic oil capacity (refill):
Semi-U tilt dozer 48 U.S. gal 180 ltr
U tilt dozer 48 U.S. gal 180 ltr
Ripper equipment (additional volume):
Giant ripper 34 U.S. gal 130 ltr
Multi-shank ripper 34 U.S. gal 130 ltr

Comments are closed.

Save Hundreds on Your Rentals

Fill out our form - takes 30 seconds - Enjoy Competing Quotes

Web Analytics