Save Hundreds on Your Rentals

Fill out our form - takes 30 seconds - Enjoy Competing Quotes

Construction Equipment Rental in Friendsville, Tennessee

Do you have a construction project coming up in Friendsville ? In case you are new in business, have equipment at a far-off location or just understand the benefits of construction equipment rentals, we can be of great assistance!

Our vendors can have the construction equipment delivered at the jobsite within a day or two.You can also pick machines and tools from convenient locations in Friendsville if you are in a position to move them on your own.

Dial our toll free number or fill out the contact form (on the right) to start receiving calls from some of the most reliable vendors in the region.

If the need be, you can personally visit the premises of any of the vendors and personally inspect their heavy construction equipment inventory to ascertain if the machines and tools are clean, latest and well maintained! We always encourage our customers to do that.

Equipment Rental Friendsville, Construction equipment rental Friendsville, Construction Friendsville, Heavy Equipment Rental Friendsville.

JCB Light Equipment FP 1540W

FP 1540W

The JCB FP1540W forward vibratory plate is 50% heavier and 71% more powerful than the FP1030W, weighing in at 91 kg and powered by a 3.6 kW Honda engine. Centrifugal force is also 50% improved at 15 kN. It's specifically designed for easy, effective compaction of asphalt, soil and other less cohesive materials.

Built for Low hand and arm vibration levels and high productivity, the FP1540W features a wear-resistant high-grade cast tamping plate for optimum durability.

It also has an oil bath lubrication system to protect its vibration bearings, shock mounts for the engine and a roll cage that also acts as a lifting bail.

The FP1540W is designed for fast travel and ultimate productivity. The options list consists of transport wheels, a water sprinkler system and rubber paving stone pads.

Compaction Performance
Operating Weight 91kg
Plate Width 400mm
Engine
Maximum Engine Power 3.6kW

KKomatsu Dozers D39PX-23
D39PXi-23 Crawler Dozer
iMC (intelligent machine control) machines have the following advantages over dozers with external grade control systems.

Innovative
Automated operation from rough dozing to finish grade.

Intelligent
New dozing mode, load control performance features.

Integrated
Standard factory installed integrated system.

No Cables
No coiled cables between machine and blade.

No Climbing
GNSS antenna and mast removed from blade.

No Connections
No daily connections required between machine and blade

Engine
Model Komatsu SAA4D95LE-6*
Type 4-cycle, water-cooled, direct injection
Aspiration Variable flow, turbocharged, air-to-air aftercooled
Number of cylinders 4
Bore x stroke 3.75" x 4.52" 95 mm x 115 mm
Piston displacement 199 in³ 3.26 ltr
Governor All-speed, electronic
Horsepower
SAE J1995 - Gross 107 HP 79 kW
ISO 9249 / SAE J1349 - Net 105 HP 78 kW
Rated rpm 2200 rpm
Fan drive type Hydraulic
Lubrication system:
Method Gear pump, force lubrication
Filter Full-flow
*EPA Tier 4 Interim and EU stage 3B emissions certified
Hydrostatic transmission
Dual-path, hydrostatic transmission provides infinite speed changes up to 5.3 km/h / 8.5 mph. The variable capacity travel motors allow the operator to select the optimum speed to match specific jobs. Travel control lock lever and neutral switch.
Travel speed (quick shift mode)* Forward Reverse
1st 0–2.1 mph
0–3.4 km/h
0–2.5 mph
0–4.1 km/h
2nd 0–3.5 mph
0–5.6 km/h
0–4.0 mph
0–6.5 km/h
3rd 0–5.3 mph
0–8.5 km/h
0–5.3 mph
0–8.5 km/h
Travel speed (variable mode) Forward Reverse
0–5.3 mph
0–8.5 km/h
0–5.3 mph
0–8.5 km/h
*Quick shift speeds are adjustable in the monitor.
FINAL DRIVE
In-shoe mounted axial piston type travel motors with integrated two stage planetary gear reduction. Compact in-shoe mount reduces risk of damaged by debris. Bolt-on sprocket ring.
STEERING SYSTEM
Palm Command Control System (PCCS) joystick control for all directional movements. Pushing the joystick forward results in forward machine travel, while pulling it rearward reverses the machine. Simply tilt the joystick to the left or right to make a turn. Tilting the joystick fully to the left or right activates counter-rotation.

Hydrostatic Transmission (HST) provides smooth powerful turns. Fully electronic control enables smooth control that can be adjusted in the monitor. The PCCS utilizes shift buttons to increase and decrease speed.

Minimum turning radius* 87" 2.2 m
*As measured by track marks on the ground at pivot turn.

 

Undercarriage
Suspension Rigid type
Track roller frame Monocoque, large section, durable construction
Rollers and idlers Lubricated track rollers
Sealed and lubricated track Track tension is easily adjusted with grease gun.
Number of track rollers (each side) 6
Type of shoes (standard) Single grouser
Number of shoes (each side) 39
Grouser height 2.1" 53 mm
Shoe width (standard) 20" 510 mm
Ground contact area 3,731 in 24072 cm²
Ground pressure
(with dozer, ROPS cab)
5.64 psi 0.40 kgf/cm² / 38.9 kPa
Track gauge 5'4" 1620 mm
Length of track on ground 7'9" 2360 mm
SERVICE REFILL CAPACITIES
Coolant 9.0 U.S. gal 34 ltr
Fuel tank 50.2 U.S. gal 190 ltr
Engine oil 2.9 U.S. gal 11 ltr
Hydraulic tank 15.8 U.S. gal 60 ltr
Final drive (each side) 0.9 U.S. gal 3.5 ltr
Operating Weight (approximate)
Tractor weight: Including ROPS cab, U frame for power angle tilt dozer, rated capacity of lubricant, coolant, full fuel tank, operator, and standard equipment.
ROPS cab 18,387 lb 8340 kg
Operating weight: Including Power Angle Tilt dozer, ROPS cab, operator, standard equipment, rated capacity of lubricant, hydraulic control unit, coolant, and full fuel tank.
ROPS cab 20,922 lb 9490 kg
hydraulic system
Closed-center Load Sensing System (CLSS) designed for precise and responsive control, and for efficient simultaneous operation.
Hydraulic control unit:
All spool control valves externally mounted remote to the hydraulic tank. Piston-type hydraulic pump with capacity (discharge flow) of 99 ltr/min 26 U.S. gal/min at rated engine rpm.
Relief valve setting 3,974 psi 27.4 MPa / 280 kg/cm²
Hydraulic cylinders Double-acting, piston type
Number of cylinders: Bore Bore
Blade lift / 2 3" 75 mm
Blade tilt / 1 3.5" 90 mm
Blade angle / 2 3.1" 80 mm
Hydraulic oil capacity (refilling):
Power angle tilt dozer 15.9 U.S. gal 60 ltr
Control valves:
3-spool control valve for power angle tilt dozer.  
Positions:  
Blade lift Raise, hold, lower, and float
Blade tilt   Right, hold, and left
Blade angle   Right, hold, and left
Additional control valve required for ripper
Positions:
Ripper lift Raise, hold, and lower

Komatsu Dozers D39EXi-23
D39EXi-23 Crawler Dozer
iMC (intelligent machine control) machines have the following advantages over dozers with external grade control systems.

Innovative
Automated operation from rough dozing to finish grade.

Intelligent
New dozing mode, load control performance features.

Integrated
Standard factory installed integrated system.

No Cables
No coiled cables between machine and blade.

No Climbing
GNSS antenna and mast removed from blade.

No Connections
No daily connections required between machine and blade.

Engine
 Model Komatsu SAA4D95LE-6*
Type 4-cycle, water-cooled, direct injection
Aspiration Variable flow, turbocharged, air-to-air aftercooled
Number of cylinders 4
Bore x stroke 3.75" x 4.52" 95 mm x 115 mm
Piston displacement 199 in³ 3.26 ltr
Governor All-speed, electronic
Horsepower
SAE J1995 - Gross 107 HP 79 kW
ISO 9249 / SAE J1349 - Net 105 HP 78 kW
Rated rpm 2200 rpm
Fan drive type Hydraulic
Lubrication system:
Method Gear pump, force lubrication
Filter Full-flow
*EPA Tier 4 Interim and EU stage 3B emissions certified
Hydrostatic transmission
Dual-path, hydrostatic transmission provides infinite speed changes up to 8.5 km/h / 5.3 mph. The variable capacity travel motors allow the operator to select the optimum speed to match specific jobs. Travel control lock lever and neutral switch.
Travel speed (quick shift mode)* Forward Reverse
1st 0–2.1 mph
0–3.4 km/h
0–2.5 mph
0–4.1 km/h
2nd 0–3.5 mph
0–5.6 km/h
0–4.0 mph
0–6.5 km/h
3rd 0–5.3 mph
0–8.5 km/h
0–5.3 mph
0–8.5 km/h
Travel speed (variable mode) Forward Reverse
0–5.3 mph
0–8.5 km/h
0–5.3 mph
0–8.5 km/h
*Quick shift speeds are adjustable in the monitor.
FINAL DRIVE
In-shoe mounted axial piston type travel motors with integrated two stage planetary gear reduction. Compact in-shoe mount reduces risk of damaged by debris. Bolt-on sprocket ring.
STEERING SYSTEM
Palm Command Control System (PCCS) joystick control for all directional movements. Pushing the joystick forward results in forward machine travel, while pulling it rearward reverses the machine. Simply tilt the joystick to the left or right to make a turn. Tilting the joystick fully to the left or right activates counter-rotation.

Hydrostatic Transmission (HST) provides smooth powerful turns. Fully electronic control enables smooth control that can be adjusted in the monitor. The PCCS utilizes shift buttons to increase and decrease speed.

Minimum turning radius* 87" 2.2 m
*As measured by track marks on the ground at pivot turn.

 

Undercarriage
Suspension Rigid type
Track roller frame Monocoque, large section, durable construction
Rollers and idlers Lubricated track rollers
Sealed and lubricated track Track tension is easily adjusted with grease gun.
Number of track rollers (each side) 6
Type of shoes (standard) Single grouser
Number of shoes (each side) 39
Grouser height 2.1" 53 mm
Shoe width (standard) 20" 510 mm
Ground contact area 3,731 in 24072 cm²
Ground pressure
(with dozer, ROPS cab)
5.64 psi 0.40 kgf/cm² / 38.9 kPa
Track gauge 5'4" 1620 mm
Length of track on ground 7'9" 2360 mm
SERVICE REFILL CAPACITIES
Coolant 9.0 U.S. gal 34 ltr
Fuel tank 50.2 U.S. gal 190 ltr
Engine oil 2.9 U.S. gal 11 ltr
Hydraulic tank 15.8 U.S. gal 60 ltr
Final drive (each side) 0.9 U.S. gal 3.5 ltr
Operating Weight (approximate)
Tractor weight: Including ROPS cab, U frame for power angle tilt dozer, rated capacity of lubricant, coolant, full fuel tank, operator, and standard equipment.
ROPS cab 18,387 lb 8340 kg
Operating weight: Including Power Angle Tilt dozer, ROPS cab, operator, standard equipment, rated capacity of lubricant, hydraulic control unit, coolant, and full fuel tank.
ROPS cab 20,922 lb 9490 kg
hydraulic system 
Closed-center Load Sensing System (CLSS) designed for precise and responsive control, and for efficient simultaneous operation.
Hydraulic control unit:
All spool control valves externally mounted remote to the hydraulic tank. Piston-type hydraulic pump with capacity (discharge flow) of 99 ltr/min 26 U.S. gal/min at rated engine rpm.
Relief valve setting 3,974 psi 27.4 MPa / 280 kg/cm²
Hydraulic cylinders Double-acting, piston type
Number of cylinders: Bore Bore
Blade lift / 2 3" 75 mm
Blade tilt / 1 3.5" 90 mm
Blade angle / 2 3.1" 80 mm
Hydraulic oil capacity (refilling):
Power angle tilt dozer 15.9 U.S. gal 60 ltr
Control valves:
3-spool control valve for power angle tilt dozer.
Positions:
Blade lift Raise, hold, lower, and float
Blade tilt   Right, hold, and left
Blade angle   Right, hold, and left
Additional control valve required for ripper
Positions:  
Ripper lift   Raise, hold, and lower

Comments are closed.

Save Hundreds on Your Rentals

Fill out our form - takes 30 seconds - Enjoy Competing Quotes

Web Analytics