Fill out our form - takes 30 seconds - Enjoy Competing Quotes
Komatsu Dozers D375A-6
D375A-6 Crawler Dozer
The D375A-6 is a great combination of power and balance; power for digging and pushing, balance for stability on slopes and for ripping. Giant or multi-shank rippers are available as is a wide lighting and maintenance options specifically designed for the demands of the mining industry. A lock-up torque converter lets the D375A-6 to shift into direct drive when pushing to increase speed and production.
4-cycle, water-cooled, direct injection
Turbocharged, air-to-air aftercooled, cooled EGR
Number of cylinders
Bore x stroke
6.69" x 6.69"
170 mm x 170 mm
All-speed and mid-range, electronic
SAE J1995 - Gross
ISO 9249/SAE J1349 - Net
Hydraulic fan at maximum speed - Net
Fan drive type
Gear pump, force lubrication
Komatsu TORQFLOW transmission consists of a water-cooled, 3-element, 1-stage, 1-phase torque converter with lockup clutch and a planetary gear, multiple-disc clutch transmission which is hydraulically actuated and force-lubricated for optimum heat dissipation. Gearshift lock lever and neutral safety switch help prevent accidental starts.
2.2 mph 3.5 km/h
2.9 mph 4.6 km/h
4.2 mph 6.8 km/h
5.5 mph 8.9 km/h
5.0 mph 8.0 km/h
6.0 mph 9.7 km/h
7.3 mph 11.8 km/h
9.8 mph 15.8 km/h
Double-reduction final drive of spur and planetary gear sets to increase tractive effort and reduce gear tooth stresses for long final drive life. Segmented sprocket teeth are bolt-on for easy replacement.
PCCS, joystick controlled, wet multiple-disc steering clutches are spring-loaded and hydraulically released.Wet multiple-disc, pedal/lever controlled steering brakes are spring-actuated hydraulically released and require no adjustment. Steering clutches and brakes are interconnected for easy, responsive steering.
Minimum turning radius
Oscillating equalizer bar and pivot shaft
Track roller frame
Cylindrical, high-tensile-strength steel construction
Rollers and idlers
Lubricated track rollers
Lubricated track rollers are resiliently mounted to the track frame with a bogie suspension system whose oscillating motion is cushioned by rubber pads.
Extreme service track shoes
Lubricated tracks. Unique seals prevent entry of foreign abrasives into pin to bushing clearances to provide extended service life. Track tension is easily adjusted with grease gun.
Number of shoes (each side)
Shoe width (standard)
Ground contact area
Ground pressure (tractor)
108 kPa / 1.10 kg/cm²
Number of track rollers
Number of carrier rollers
Extreme service shoes:
Ground contact area:
24'' / 610 mm Additional weight - 0 lb / 0 kg
7,527 in² 48560 cm²
21.0 psi 1.48 kgf/cm² / 145 kPa
28'' / 710 mm Additional weight - 1,500 lb / 680 kg
8,760 in² 56520 cm²
18.2 psi 1.28 kgf/cm² / 126 kPa
32'' / 810 mm Additional weight - 3,000 lb / 1360 kg
9,990 in² 64480 cm²
16.0 psi 1.13 kgf/cm² / 111 kPa
** Ground pressure based on tractor, Semi-U tilt dozer, giant ripper, cab, ROPS, operator, standard equipment, rated capacity of lubricant, coolant, and full fuel tank.
Coolant and Lubricant Capacity (refill)
317.0 U.S. gal
31.7 U.S. gal
22.7 U.S. gal
Torque converter, transmission, bevel gear, and steering system
39.6 U.S. gal
Final drive (each side)
17.1 U.S. gal
Tractor weight Including rated capacity of lubricant, coolant, full fuel tank, operator, and standard equipment.
Including Semi-U tilt dozer, giant ripper, cab, ROPS, operator, standard equipment, rated capacity of lubricant, coolant, and full fuel tank.
1.48 kg/cm² / 145 kPa
Hydraulic control unit:
Closed-center load sensing system (CLSS) designed for precise and responsive control, and for efficient simultaneous operation.
Hydraulic control unit::
All spool control valves externally mounted beside the hydraulic tank. Variable piston pump with capacity (discharge flow) of 366 ltr/min / 96.7 U.S. gal/min for implement at rated engine rpm.
Relief valve setting . . . for implement
27.5 MPa 280 kg/cm²
Spool control valves for Semi-U tilt dozer and Full-U tilt dozer.
Raise, hold, lower, and float
Right, hold, and left
Additional control valve required for variable digging angle multi-shank ripper and giant ripper.