get multiple quotes Heavy Rentals Equipment on Facebook

Save Hundreds on Your Rentals

Fill out our form - takes 30 seconds - Enjoy Competing Quotes

Construction Equipment Rental in Clio, Michigan

You need not go all out with a construction equipment rental model but it is true that renting heavy construction equipment does provide you with significant borrowing power by improving your assets to liabilities ratio.

So, even if you have your core fleet ready, it makes sense to supplement it with necessary machinery available on rent. Since rental services in Clio are a lot more flexible than leasing any day, especially in terms of the length of contract, you can strike the right balance between buying, leasing and renting construction equipment.

If you have made up your mind to avail heavy construction equipment rental services, we can assist you in finding the most trusted and responsive vendors in Clio.

You can gain access to our network of established and reliable vendors any day. You just have to submit the online contact form (on the right). You can also make a quick call on our toll free number anytime.

Equipment Rental Clio, Construction equipment rental Clio, Construction Clio, Heavy Equipment Rental Clio.

Unable to parse entered address. API response code: REQUEST_DENIED

Komatsu Excavators HB215LC-1

HB215LC-1 Hybrid Excavator

The HB215LC-1 uses groundbreaking swing regeneration hybrid technology to save up to an average of 25% in fuel consumption and a like amount in emissions. By capturing the energy that normally would be lost during swing braking in a capacitor, the energy can then be used to power the swing and has energy left to boost the engine by up to 60 horsepower. And all this is done without losing any performance over a standard excavator. And by the way, the Hybrid Excavator HB215LC-1 is very quiet, which is great when working in urban areas.

Engine
Model Komatsu SAA4D107E-1-A
Type Water cooled, 4-cycle, direct injection
Aspiration Turbocharged and aftercooled
Number of cylinders 1
Bore 4.21" 107 mm
Stroke 4.88" 124 mm
Piston displacement 272 in³ 4.46 ltr
Horsepower:
SAE J1995 - Gross 148 HP 110 kW
ISO 9249 / SAE J1349 - Net 139 HP 104 kW
Rated rpm 2000 rpm
Fan drive type Mechanical
Governor All-speed control, electronic
*EPA Tier 4 Interim and EU stage 3B emissions certified
Hydraulics
Type . . HydrauMind (Hydraulic Mechanical Intelligence New Design) system, closed-center system with load sensing valves and pressure compensated valves
Number of selectable working modes 5
Main pump:
Type Variable displacement piston type
Pumps for Boom, arm, bucket, swing, and travel circuits
Maximum flow 116 U.S. gal/min 439 ltr/min
Supply for control circuit Self-reducing valve
Hydraulic motors:
Travel 2 x axial piston motors with parking brake
Relief valve setting:
Implement circuits 5,400 psi 380 kgf/cm²/ 37.3 MPa
Travel circuit 5,400 psi 380 kgf/cm² / 37.3 MPa
Pilot circuit 470 psi 33 kgf/cm² / 3.2 MPa
Hydraulic cylinders:
Number of cylinders Bore x Stroke x Rod Diameter Bore x Stroke x Rod Diameter
Boom / 2 4.7" x 52.5" x 3.3" 120 mm x 1334 mm x 85 mm
Arm / 1 5.3" x 58.7" x 3.7" 135 mm x 1490 mm x 95 mm
Bucket for 2.41 m 7'11" and 2.93 m 9'7" Arm / 1 4.5" x 44.1" x 3.2" 115 mm x 1120 mm x 80 mm
Drives and Brakes
Steering control Two levers with pedals
Drive method Hydrostatic
Maximum drawbar pull 40,120 lb 178 kN / 18200 kg
Gradeability 35° 70%
Maximum travel speed: (Auto-Shift)
High 3.4 mph 5.5 km/h
Mid 2.5 mph 4.1 km/h
Low 1.9 mph 3.0 km/h
Service brake Hydraulic lock
Parking brake Mechanical disc brake
Undercarriage
Center frame X-frame
Track frame Box-section
Seal of track Sealed track
Track adjuster Hydraulic
Number of shoes 49 each side
Number of carrier rollers 2 each side
Number of track rollers 9 each side
Coolant and Lubricant Capacity refilling
Fuel tank 105.7 U.S. gal 400 ltr
Coolant (Engine) 4.6 U.S. gal 17.3 ltr
(Hybrid) 1.4 U.S. gal 5.2 ltr
Final drive, each side 0.9 U.S. gal 3.3 ltr
Swing drive 1.9 U.S. gal 7.1 ltr
Swing motor 0.4 U.S. gal 1.6 ltr
Generator motor 1.6 U.S. gal 6.0 ltr
Hydraulic tank 35.7 U.S. gal 135 ltr
Operating Weight (APROXIMATE)
Operating weight including 5700 mm / 18'8" one-piece boom, 2925 mm / 9'7" arm, SAE heaped 0.80 m³ / 1.05 yd³ backhoe bucket, rated capacity of lubricants, coolant, full fuel tank, operator, and standard equipment.
HB215LC-1 Shoes 31.5" 800 mm
Operating Weight 48,175 lb 21850 kg
Ground Pressure 4.9 psi 0.35 kg/cm²
33.9 kPa

 

Komatsu Excavators PC650LC-8 MH
PC650LC-8 MH Material Handler (55'-60' Reach)

If your needs require long reach and high stability in an excavator to handle material with grapples, clams or magnets, the PC650LC-8 material handler has the boom and arm combinations you'll need.

Engine
Model Komatsu SAA6D140E-5*
Type Water-cooled, 4-cycle, direct injection
Aspiration Turbocharged, aftercooled, cooled EGR
Number of cylinders 6
Bore 5.51" 140 mm
Stroke 6.50" 165 mm
Piston displacement 930 in³ 15.24 ltr
Governor All-speed, electronic
Horsepower:
SAE J1995 (Gross) 433 HP 323 kW
ISO9249 / SAE J1349 (Net) 429 HP 320 kW
Hydraulic fan at maximum speed (Net) 386 HP 288 kW
Rated rpm 1800 rpm
Fan drive type Hydraulic
*EPA Tier 3 and EU stage 3A emissions certified
Hydraulics
Type Open-center load-sensing system
Number of selectable working modes 3
Main pump:
Type Variable capacity piston pump
Pumps for Boom, arm, bucket, swing, and travel circuits
Maximum flow 2 x 108 U.S. gpm 2 x 410 ltr/min
Sub-pump for control circuit Gear pump
Hydraulic motors:
Travel 2 x axial piston motor with parking brake
Swing 2 x axial piston motor with swing holding brake
Fan drive pump Variable capacity
Relief valve setting:
Implement circuits 4,620 psi 31.9 MPa 325 kg/cm²
Travel circuit 4,980 psi 34.3 MPa 350 kg/cm²
Swing circuit 3,700 psi 25.5 MPa 260 kg/cm²
Pilot circuit 430 psi 2.9 MPa 30 kg/cm²
Hydraulic cylinders / Number of cylinders: Bore x Stroke: Bore x Stroke:
Boom / 2 7.5" x 61.5" x 5.0" 190 mm x 1562 mm x 127 mm
Arm / 1 7.5" x 78.0" x 5.0" 190 mm x 1981 mm x 127 mm
Drives & Brakes
Steering control Two levers with pedals
Drive method Fully hydrostatic
Travel motor Axial piston motor, in-shoe design
Reduction system Planetary double reduction
Maximum drawbar pull 93,250 lb 415 kN / 42300 kg
Gradeability 70%
Maximum travel speed:
Low 1.9 mph 3.0 km/h
High 3.0 mph 4.9 km/h
Service brake Hydraulic lock
Parking brake Oil disc brake
Swing System
Driven method Hydraulic motors (2)
Swing reduction Planetary gear
Swing circle lubrication Grease-bathed
Swing lock Oil disc brake
Swing speed 8.3 rpm
Swing torque 154,481 ft. lbs. 21365 kg•m
Undercarriage
Center frame H-leg frame
Track frame Box-section
Track type Sealed
Track adjuster Hydraulic
Number of shoes (each side) 52
Number of carrier rollers (each side) 3
Number of track rollers (each side) 9
Coolant and Lubricant Capacity (refilling)
Fuel tank 232.5 U.S. gal 880 ltr
Radiator 15.3 U.S. gal 58 ltr
Engine 10.6 U.S. gal 40 ltr
Final drive, each side 2.6 U.S. gal 10 ltr
Swing drive 2 x 3.4 U.S. gal 2 x 13 ltr
Hydraulic tank 95.0 U.S. gal 360 ltr
Operating Weight (approximate)
Operating weight without grapple
16.8 m / 55'
3302 mm / 130" gauge 139,424 lb 63242 kg
4064 mm / 160" gauge 149,224 lb 67687 kg
18.3 m 60'
3302 mm / 130" gauge 140,838 lb 63883 kg
4064 mm / 160" gauge 150,638 lb 68329 kg

Komatsu Excavators PC88MR-8
PC88MR-8 Hydraulic Excavator

The PC88MR-8 is a link between minis and mid-size excavators. The PC88MR-8 Hydraulic Excavator has a swing boom, tight tail swing, three track options and backfill blade like a mini but is built to have the reliability and durability of larger excavators.

Engine
Model Komatsu SAA4D95LE-5
Type Water cooled, 4-cycle, direct injection
Aspiration Turbocharged, and air-to-air aftercooled
Number of cylinders 4
Piston displacement 199 in³ 3.26 ltr
Horsepower @ 1950 rpm:
Net (ISO 9249/SAE J1349) 65 HP 49 kW
Electric System
Operation voltage 24 V
Battery 55 Ah/2 x 12
Alternator 35 A/24 V
Starter 4.5 kW/24 V
Hydraulic System
Type - HydrauMind (Hydraulic Mechanical Intelligence New Design) system, Closed-center system with load-sensing valves and pressure-compensated valves
Main pumps:
Type Variable displacement, axial piston
Maximum flow 42.3 u.s. gal/min 160 ltr/min
Type Fixed displacement gear
Maximum flow 18.5 U.S. gal/min 70 ltr/min
Hydraulic motors:
Travel 2 x piston motor with parking brake
Swing 1 x piston motor with swing holding brake
Relief valve setting:
Implement, travel circuit 3,840 psi 26.5 MPa / 270 kgf/cm²
Swing and blade circuit 3,060 psi 21.1 MPa 215 kgf/cm²
Performance
Travel speed:
High 3.2 mph 5.1 km/hr
Low 1.8 mph 2.9 km/hr
Swing speed 10 rpm
Ground pressure 5.4 psi 0.38 kg/cm²
Max. drawbar pull 15,050 lbf 66.9 kN / 6820 kgf
Gradeability 35°
Bucket digging force (ISO) 13,780 lb 6250 kg
Arm crowd force (ISO) 8,160 lb 3700 kg
Swing System
Driven by Hydraulic motor
Swing reduction Planetary gear
Swing circle lubrication Grease-bathed
Swing lock Automatic, with oil immersed discs
Drives & Brakes
Steering control Two levers with pedalsr
Drive method Fully hydrostatic
Service brake Hydraulic lock
Parking brake Mechanical disc
Undercarriage
Center frame X-frame
Track frame Box-section
Track type Sealed track
Track adjuster Hydraulic
Number of carrier rollers 1 each side
Number of track rollers 5 each side
Refill Capacities
Fuel tank 33.0 u.s. gal 125 ltr
Radiator 2.6 u.s. gal 10 ltr
Engine 2.9 u.s. gal 11 ltr
Final drive, each side 0.3 u.s. gal 1.1 ltr
Swing drive 0.7 U.S. gal 2.8 ltr
Hydraulic tank 14.8 u.s. gal 56 ltr

 

Operating Weight (approximate)
Operating weight including 3405 mm / 11'2" one-piece boom, 2100 mm / 6'11" arm, SAE heaped 0.28 m³ / 0.37 yd³ backhoe bucket, blade, rated capacity of lubricants, coolant, full fuel tank, operator, and standard equipment.
Operating weight 18,558 lb 8420 kg

Comments are closed.

Save Hundreds on Your Rentals

Fill out our form - takes 30 seconds - Enjoy Competing Quotes

Web Analytics